Menu
Professional Remanufacturer of Golf Cart Speed Controllers
HOME
REPAIR YOUR PART
CASH FOR CORES
Go!
Photo
Make
Title
Description
OE
Part Number
GolfRama
Part Number
Price
E-Z-GO
Speed Controller 36V 350amp
PDS Shunt Controller ITS Throttle Input
Upgraded to 350Amp PDS Shunt Controller ITS Throttle Input. Electronic Speed Controller (PDS/VPS) is used on 1994-current E-Z-GO Medalist & TXT Models with the PDS (Precision Drive System) and/or VPS (Vehicle Performance System) applications for Golf Cars and Vehicles to enhance power and speed while maintaining the E-Z-GO Safety Standards for each vehicle. The speed controller is responsible for regulating the speed levels and performance of your vehicle. There are three large terminals on the end of the controller (A1, B- and B+) and two smaller terminals on the opposite end (F1, F2). CHECK MOTOR WINDINGS: 1- Set your VOM to RESISTANCE (O). 2- With your motor disconnected, measure A1 to A2. This must measure BETWEEN .3O and 1O. 3- With your motor disconnected, measure F1 to F2. This must measure BETWEEN 1O and 2O. 4- With your motor disconnected, measure A1 to F1. This must measure OPEN. 5- With your motor disconnected, measure F1 to the motor case. This must measure greater than 5MO. CHECK the MAIN SOLENOID: 1- Disconnect all wires from the main solenoid. 2- Set your VOM to RESISTANCE (O). 3- Measure the solenoid coil. This must measure NO LESS than 100O. 4- Connect VOM leads to the main solenoid lugs. 5- Attach jumpers from the main battery positive and negative to the coil (small terminals). 1- The meter must jump from infinity to LESS THAN .3O. 2-Remove jumpers and reconnect solenoid wiring from the harness. (If suppression diode is present. The non-banded side must go the blue wire – pin J1-6 from the controller) This cart is capable of diagnostics! Placing the cart in the diagnostics mode will allow the controller to use the back-up alarm to beep out codes. Do not underestimate the usefulness of this tool. There is an orange and white sticker on the environmental cover that explains how to enter the diagnostics mode.
73326G0x Upgraded, 73326G0xUpgraded
G633P
$259.00
$239.00
Club Car
DC Motor Controller 48V 500Amp
DC Motor Controller 48V 500Amp
Curtis 48V 500A (CLUB CAR) ERIC Controller (MCOR)
1515S-5306, 1515S5306
G1436
$259.00
E-Z-GO
Speed Controller 36V 275amp
Speed Controller 36V 275Amp
ITS Throttle Input, Early version with 4 blades. Curtis Motor Controller 1206 TXT Cars (MED/TXT), 5 Pin. Electronic Speed Controller is used on 1994-current E-Z-GO Medalist and TXT 36 Volt Series Electric Vehicles. The speed controller is responsible for regulating the speed levels of your vehicle. This particular speed controller not designed for use with DCS (Drive Control System) or PDS (Precision Drive System) vehicle applications Series Motor Controller Only, This is not a Separately Excited (Sep Ex) motor controller and will not work with shunt wound electric motors. How to know if the old controller is bad Controller 1- (-) to B- terminal (+) to B+ terminal. The pedal not pressed in 20 minutes. Should show the battery pack voltage. slowly depress the pedal the reading should go down to 0 volts. 2- M- to B+ (with F/R in F). The voltage should go from Zero when the solenoid clicks to full pack voltage when pedal is on floor Motor Test 3- O ohms Test should have continuity present between F1 and F2 and between A1 and A2 NO CONTINUITY between A and F
1206-04, 120604
G632-4
$339.00
$299.00
Curtis
DC Motor Controller 36V 300Amp
24-36V
1207-2103, 12072103
G733
$299.00
Club Car
DC Motor Controller 48V 350Amp
DC Motor Controller 48V 350Amp
Club Car Precedent Excel i2, 2008 - Up Replaces Stock Controller 1515-5201 and others Designed to be used with motor #'s 3258, 3294, and Stock Motors Speeds up to 19mph with Stock Motor
1515S-5301, 1515S5301
G143
$339.00
Multi
DC Motor Controller 48V 350Amp
Speed Controller 48V 350amp
48V golf carts with the IQ electrical system
1510A-5351, 1510A5351
G43
$269.00
John Deere
Speed Controller 48V 400amp
1264-5403 48V 400A (0-5K) Sx Control
1264-5403, 12645403
G6444
$279.00
Multi
DC Motor Controller 48V 500Amp
Remanufactured Curtis 1268-5501 48 Volt 500 Amp Controller •Not a Series motor controller and will not work with series wound electric motors. • 48V, 500A Controller
1268-5501, 12685501
G12685501
$359.99
Curtis
Speed Controller 36V 300amp
Sepex
24V-36V Separately Excited Motor Controller
1243-4320, 12434320
G333
$299.00
Curtis
Speed Controller 36V 300amp
Sepex Traction Controller
CURTIS 1243-4301, SepEx Traction Controller, 24-36V, 300A
1243-4301, 12434301
G343
$699.00
Curtis
Speed Controller 48V 275amp
1204-404 36/48V 275A (0-5K) Pmc
1204-404, 1204404
G442-4
$279.00
Curtis
Speed Controller 36V 400amp
1205-116 24/36V 400A (5K-0) Pmc
1205-116, 1205116
G534
$279.00
Curtis
Speed Controller 48V 275amp
1204-202, 1204202
G442-2
$279.00
Curtis
Speed Controller 24V 200amp
Curtis 24/36V 275A (5K-0) PMC 1204-002
1204-002, 1204002
G422
$279.00
Curtis
Speed Controller 48V 500amp
1244-6502m Curtis 36/84V 500A (5K-0) SX Controller
1244-6502, 12446502
G4445
$279.00
Curtis
Speed Controller 48V 400amp
1244-5451, 12445451
G4444
$279.00
Club Car
Speed Controller 48V 350amp
Upgraded
Upgraded to 350Amp ITS Throttle Input 0-5K 36-48V
1204-401 350A, 1204401350A
G443
$239.00
E-Z-GO
DC Motor Controller 48V 250Amp
Throttle: ITS
1206 DC Motor Controller 48V 250 Amp Cart: E-Z-GO TXT 48, Throttle: ITS Fits E-Z-GO 48-Volt Models: 2014 TXT 2012-2014 Terrain 250 2011-2012 ST Sport II 2011-2012 MPT 800/1000 2012-2014 Express S4 & L4 2012-2013 Shuttle 4X 2012 Cushman Hauler 800/1000
1206HB-5201, 1206HB5201
G642HB
$269.00
$279.00
Club Car
Speed Controller 36V 600amp
Upgraded
Upgraded 600Amp 1205 117 Used on 1995-Current E-Z-GO TXT, Shuttle 950 Series, XI-875/881 and Workhorse/MPT (Multi-Purpose Truck) 1000, This controller is rated 36 Volts and 600 Amps, Controllers are the most vulnerable to damage from lightning
1205-117 600A, 1205117600A
G536I
$279.00
Curtis
Speed Controller 48V 550amp
Upgraded
Upgraded 1205
1205 Upgraded, 1205Upgraded
G545
Multi
Speed Controller 48V 400amp
Upgraded
Upgraded to 400Amp ITS Throttle Input, Throttle Input 0-5K
1204-401 400A, 1204401400A
G444
$249.00
Club Car
Speed Controller 48V 300amp
Reverse Throttle Input 5K-0 Ohm
Reverse Throttle Input 5K-0 Ohm Curtis 1204-412 36/48 Volt 300 Amp PMC Controller has A2 Blade for plug braking
1204-412, 1204412
G443R
$239.00
Club Car
Speed Controller 48V 600amp
Upgraded
Upgraded to 600Amp Reverse Throttle Input 5K-0 Ohm Curtis 1204-410 36/48 Volt 400 Amp PMC Controller has A2 Blade for plug braking Club Car Part Number: 101840201
1204-410 600A, 1204410600A
G446R
$299.00
Club Car
Speed Controller 48V 275amp
ITS Throttle Input 0-5K 36-48V
Upgrades to 350Amp (G443) or 400Amp (G444) ITS Throttle Input 0-5K 36-48V
1204-401, 1204401
G442
$229.00
E-Z-GO
Speed Controller 36V 350amp
Upgraded
Upgraded to 350Amp ITS Throttle Input When it's time to replace the Controller, you should also check the Motor since extreme conditions such as lightning can cause both the Controller and Motor permanent damage. 1206 Upgraded 350Amp, 5-pin controller Controllers are the most vulnerable to damage from lightning This Electronic Speed Controller is used on 1994-current E-Z-GO Medalist and TXT 36-Volt Series Electric Vehicles. The speed controller is responsible for regulating the speed levels of your vehicle.This particular speed controller is not designedfor use with DCS (Drive Control System) or PDS (Precision Drive System) vehicle applications
1206-4301, 12064301
G633
$149.00
$149.00
E-Z-GO
Speed Controller 36V 275amp
PDS Shunt Controller ITS Throttle Input
Upgrades to 350Amp G633P PDS Shunt Controller ITS Throttle Input. Electronic Speed Controller (PDS/VPS) is used on 1994-current E-Z-GO Medalist & TXT Models with the PDS (Precision Drive System) and/or VPS (Vehicle Performance System) applications for Golf Cars and Vehicles to enhance power and speed while maintaining the E-Z-GO Safety Standards for each vehicle. The speed controller is responsible for regulating the speed levels and performance of your vehicle. There are three large terminals on the end of the controller (A1, B- and B+) and two smaller terminals on the opposite end (F1, F2). CHECK MOTOR WINDINGS: 1- Set your VOM to RESISTANCE (O). 2- With your motor disconnected, measure A1 to A2. This must measure BETWEEN .3O and 1O. 3- With your motor disconnected, measure F1 to F2. This must measure BETWEEN 1O and 2O. 4- With your motor disconnected, measure A1 to F1. This must measure OPEN. 5- With your motor disconnected, measure F1 to the motor case. This must measure greater than 5MO. CHECK the MAIN SOLENOID: 1- Disconnect all wires from the main solenoid. 2- Set your VOM to RESISTANCE (O). 3- Measure the solenoid coil. This must measure NO LESS than 100O. 4- Connect VOM leads to the main solenoid lugs. 5- Attach jumpers from the main battery positive and negative to the coil (small terminals). 1- The meter must jump from infinity to LESS THAN .3O. 2-Remove jumpers and reconnect solenoid wiring from the harness. (If suppression diode is present, The non-banded side must go the blue wire – pin J1-6 from the controller.) This cart is capable of diagnostics! Placing the cart in the diagnostics mode will allow the controller to use the back-up alarm to beep out codes. Do not underestimate the usefulness of this tool. There is an orange and white sticker on the environmental cover that explains how to enter the diagnostics mode
1206 MX PDS, 1206MXPDS
G632P
$239.00
$219.00
E-Z-GO
Speed Controller 36V 300amp
ITS Throttle Input
1206 SX for DCS Cars 9 pin controller Electronic Speed Controller is used on 1994-2000 E-Z-GO Electric with DCS (Drive Control System). Note: There are 3 large terminals (A1, B-, A2/B+), 2 smaller ones (F1, F2) and the 9-pin connector
1206 SX DCS, 1206SXDCS
G632D
$269.00
$249.00
E-Z-GO
Speed Controller 36V 275amp
ITS Throttle Input
Upgrades to 350Amp G633 ITS Throttle Input Later version with 3 blades. Curtis Motor Controller 1206 TXT Cars (MED/TXT), 5 Pin. Electronic Speed Controller is used on 1994-current E-Z-GO Medalist and TXT 36 Volt Series Electric Vehicles. Speed controller is responsible for regulating the speed levels of your vehicle.This particular speed controllers not designed for use with DCS (Drive Control System) or PDS (Precision Drive System) vehicle applications Series Motor Controller Only, This is not a Separately Excited (Sep Ex) motor controller and will not work with shunt wound electric motors. How to know if the old controller is bad Controller 1- (-) to B- terminal (+) to B+ terminal. Pedal not pressed in 20 minutes. Should show the battery pack voltage. slowly depress the pedal the reading should go down to 0 volts. 2- M- to B+ (with F/R in F). The voltage should go from Zero when solenoid clicks to full pack voltage when pedal is on floor Motor Test 3- O ohms Test should have continuity present between F1 and F2 and between A1 and A2 NO CONTINUITY between A and F
25864G09, 25864G09
G632
$149.00
$149.00
Club Car
Speed Controller 48V 350amp
1205-210 36/48V 350A (ITS)
1205-210, 1205210
G543I
$259.00
$249.00
Multi
DC Motor Controller 48V 400Amp
Sepex
PDS II Programmable Electronic Speed Controller Sepex PDS II, 48V 400A (ITS) SX Controller Fits EZGO 2000-Up PDS systems E-Z-GO MPT Utility Vehicle
1264-5407, 12645407
G12645407
$469.00
$449.00
Club Car
Speed Controller 36V 400amp
Upgrades to 350Amp (G536I) The vehicle's speed controller is used to vary the speed of an electric motor and it's direction. This OEM (Original Equipment Manufacturer) Speed Controller-ESCII-HD (Curtis 1205-117) is used on 1995-current E-Z-GO TXT, Shuttle 950 Series, XI-875/881 and Workhorse/MPT (Multi-Purpose Truck) 1000. -Used on 1995-Current E-Z-GO TXT, Shuttle 950 Series, XI-875/881 and Workhorse/MPT (Multi-Purpose Truck) 1000 -Controllers are the most vulnerable to damage from lightning -This controller is rated 36 Volts and 400 Amps ***ITS***
1205-117, 1205117
G534I
$269.00
Forklift
Speed Controller 48V 450amp
Forklift
Curtis 36/48V 450A (5K-0) PMC
1204S-5403, 1204S5403
G444S
$249.00
Club Car
Speed Controller 48V 400amp
Upgraded
Upgraded to 400Amp Reverse Throttle Input 5K-0 Ohm Curtis 1204-410 36/48 Volt 400 Amp PMC Controller has A2 Blade for plug braking Club Car Part Number: 101840201
1204-410 400A, 1204410400A
G444R
$249.00
Club Car
Speed Controller 48V 400amp
Upgraded
Upgraded to 400Amp 95 Power Drive Only Club Car DS 1995-1996, 400 Amp, 36-48 Volt Curtis 1204-413 4 buss bars and 5k-0 throttle
1204-413 400A, 1204413400A
G444P
$249.00
Club Car
Speed Controller 48V 350amp
Upgraded
Upgraded to 350Amp 95 Power Drive Only Club Car DS 1995-1996, 350 Amp, 36-48 Volt Curtis 1204-413 4 buss bars and 5k-0 throttle
1204-413 350A, 1204413350A
G443P
$229.00
Club Car
Speed Controller 48V 225amp
Reverse Throttle Input 5K-0 Ohm
Upgrades 400Amp (G444R) Reverse Throttle Input 5K-0 Ohm Curtis 1204-410 36/48 Volt 225 Amp PMC Controller has A2 Blade for plug braking Club Car Part Number: 101840201
1204-410, 1204410
G442R
$249.00
$229.00
Club Car
Speed Controller 48V 275amp
95 Power Drive Only
Upgrades to 350Amp G443P or 400Amp G444P 95 Power Drive Only Club Car DS 1995-1996. 275 Aamp, 36-48 Volt Curtis 1204-413 4 buss bars and 5k-0 throttle
1204-413, 1204413
G442P
$249.00
$229.00
Multi
Speed Controller 36V 400amp
Upgraded
Upgraded to 400Amp With High Pedal Disable (HPD) and Plug Brake Terminal 400 Amp / 24-36 Volt Curtis #1204-001 / 05-K Throttle Input Fits Club Car, Columbia, E-Z-GO, Nordskop and Melex and others
1204-001 400A, 1204001400A
G434H
$279.00
Club Car
Speed Controller 36V 400amp
Upgraded
Upgraded to 400Amp No High Pedal Disable * Fits Club Car Golf Carts * For 36V Electric Carts Years 1990-1994 * 400 Amp / 24-36 Volt * Curtis #1204-012 / 05-K Throttle Input
1204-012 400A, 1204012400A
G434
$279.00
Multi
Speed Controller 36V 350amp
Upgraded
Upgraded to 350Amp With High Pedal Disable (HPD) and Plug Brake Terminal 350 Amp / 24-36 Volt Curtis #1204-001 / 05-K Throttle Input Fits Club Car, Columbia, E-Z-GO, Nordskop and Melex and others
1204-001 Upgraded, 1204001Upgraded
G433H
$259.00
Club Car
Speed Controller 36V 350amp
Upgraded
Upgraded to 350Amp No High Pedal Disable * Fits Club Car Golf Carts * For 36V Electric Carts Years 1990-1994 * 350 Amp / 24-36 Volt * Curtis #1204-012 / 05-K Throttle Input
1204-012 350A, 1204012350A
G433
$259.00
Multi
Speed Controller 36V 275amp
High Pedal Disable (HPD)
Upgrades to 350Amp (G433H) or 400Amp (G434H) With High Pedal Disable (HPD) and Plug Brake Terminal 275 Amp / 24-36 Volt Curtis #1204-001 / 05-K Throttle Input Fits Club Car, Columbia, E-Z-GO, Nordskop and Melex and others
1204-001, 1204001
G432H
$259.00
$239.00
Club Car
Speed Controller 36V 275amp
No High Pedal Disable (HPD)
Upgrades to 350Amp (G433) or 400Amp (G434) No High Pedal Disable Fits Club Car Golf Carts For 36V Electric Carts Years 1990-1994 275 Amp / 24-36 Volt Curtis 1204-012 / 05-K Throttle Input
1204-012, 1204012
G432
$239.00
Club Car
Speed Controller 36V 175amp
ITS Throttle Input 0-5K
ITS Throttle Input 0-5K
1204-301, 1204301
G431
$239.00
Club Car
Speed Controller 48V 400amp
Upgraded 400Amp
Upgraded to 4000Amp 48V golf carts with the IQ electrical system 101-9565-01, 1510-5250, 1510-5251, 1510A-5250, 1510A-5251 Club Car IQ (DS AND PRECEDENT) 2000-2008
1510A-5250 400A, 1510A5250400A
G44
$279.00
Club Car
Speed Controller 48V 250amp
Club Car IQ Controller
Upgrades to 350Amp G43 48V golf carts with the IQ electrical system 101-9565-01, 1510-5250, 1510-5251, 1510A-5250, 1510A-5251 Club Car IQ (DS AND PRECEDENT) 2000-2008
1510A-5250, 1510A5250
G42
$259.00
Club Car
Speed Controller 24V 200amp
Curtis 24V 200Amp PM Motor Controller
1213-5101, 12135101
G322
$249.00
Yamaha
Speed Controller 36V 275amp
Motor Control Unit
Unit with cable and 2 white connectors For Yamaha G11, G14, G16 carts Yamaha G11 - P/N JN4-86510-00 Yamaha G14 - P/N JN4-86510-01 Yamaha G16 - P/N JN4-86510-02
JN4-86510-0x, JN4865100x
G32
$299.00
General Electric
Speed Controller 48V 260amp
Speed Controller 48V 260amp
JU2-H6510-00, JU2H651000
G22E
$249.00
E-Z-GO
DC Motor Controller 48V 500Amp
Sepex
Remanufactured Curtis 1520-5501 48 Volt 500 Amp Controller IQ Plus Club Car •Not a Series motor controller and will not work with series wound electric motors. • 48V, 500A MCOR Controller
1520-5501, 15205501
G15205501
$359.99
Multi
DC Motor Controller 48V 400Amp
Sepex
DC Motor Controller 48V 400Amp 1268-5403, 36-48V / 400A, working with 3-wire potentiometer throttle and 0-5V voltage throttle CURTIS Model: 1268-5403 Nominal Battery Voltage (Volts): 48V (default setting) or 36V Amature 2-minute current rating (amps): 400 Field 2 minute current rating (amps): 50 Logic enable and logic power input voltage (minimum): 16.8 V Logic enable and logic power input current (no contactors engaged): 160 mA without programmer; 200 mA with programmer Logic input voltage: 20.0 V High; 7.5 V Low Logic input current 10 mA Throttle Type: various throttles can be used with the 1268 controller, including 5kO 3-wire potentiometers and 0–5V throttles. Dimensions: L229xW178xH81 mm Net Weight: 3.9 kg
1268-5403, 12685403
G12685403
$359.99
Multi
DC Motor Controller 48V 400Amp
Sepex
Curtis 36/48V 400A (0-5V) SX Controller
1244-5406, 12445406
G12445406
$359.99
Part Selection
Make
Model
Year
Product Type